BCDコードエンコーダ_ちくじシフトほう
9023 ワード
September 14,2016作者:dengshuai_super出典:http://blog.csdn.net/dengshuai_super/article/details/52541402声明:転載は作者と出典を明記してください.
BCDコードエンコーダ(Binary-BCD Converter)ちくじシフトほう
徐々に左に移動し、BCD 0が11に移動すると3<4に等しく、調整する必要はない.BCD 0が111にシフトすると7>4に等しく、3を加えると10に等しく、対応するバイナリは1010である.再シフト後、BCD 1は1であり、BCD 0は0101で5>4に等しく、3を加えると8に等しい対応するバイナリは1000である.再びシフトし、BCD 1=11、BCD 0=001、bin=11である.BCD 1とBCD 0はいずれも<4であるため、動作しない.再びシフトして、BCD 1=110、BCD 0=001、bin=1、BCD 1=6>4のため、3を加えると9になり、対応するバイナリは1001であり、このときBCD 1=1001、BCD 0=001、bin=1である.最後のシフト:BCD 2=1,BCD 1=010,BCD 0=1111.
ソース:https://ke.qq.com/user/tasks/index.html?cid=117307#tid=100127911&fr=2
BCDコードエンコーダ(Binary-BCD Converter)ちくじシフトほう
徐々に左に移動し、BCD 0が11に移動すると3<4に等しく、調整する必要はない.BCD 0が111にシフトすると7>4に等しく、3を加えると10に等しく、対応するバイナリは1010である.再シフト後、BCD 1は1であり、BCD 0は0101で5>4に等しく、3を加えると8に等しい対応するバイナリは1000である.再びシフトし、BCD 1=11、BCD 0=001、bin=11である.BCD 1とBCD 0はいずれも<4であるため、動作しない.再びシフトして、BCD 1=110、BCD 0=001、bin=1、BCD 1=6>4のため、3を加えると9になり、対応するバイナリは1001であり、このときBCD 1=1001、BCD 0=001、bin=1である.最後のシフト:BCD 2=1,BCD 1=010,BCD 0=1111.
module binary_to_bcd (
clk_i,
ce_i,
rst_i,
start_i,
dat_binary_i,
dat_bcd_o,
done_o
);
parameter BITS_IN_PP = 16; // # of bits of binary input
parameter BCD_DIGITS_OUT_PP = 5; // # of digits of BCD output
parameter BIT_COUNT_WIDTH_PP = 4; // Width of bit counter
// I/O declarations
input clk_i; // clock signal
input ce_i; // clock enable input
input rst_i; // synchronous reset
input start_i; // initiates a conversion
input [BITS_IN_PP-1:0] dat_binary_i; // input bus
output [4*BCD_DIGITS_OUT_PP-1:0] dat_bcd_o; // output bus
output done_o; // indicates conversion is done
reg [4*BCD_DIGITS_OUT_PP-1:0] dat_bcd_o;
// Internal signal declarations
reg [BITS_IN_PP-1:0] bin_reg;
reg [4*BCD_DIGITS_OUT_PP-1:0] bcd_reg;
wire [BITS_IN_PP-1:0] bin_next;
reg [4*BCD_DIGITS_OUT_PP-1:0] bcd_next;
reg busy_bit;
reg [BIT_COUNT_WIDTH_PP-1:0] bit_count;
wire bit_count_done;
//--------------------------------------------------------------------------
// Functions & Tasks
//--------------------------------------------------------------------------
function [4*BCD_DIGITS_OUT_PP-1:0] bcd_asl;
input [4*BCD_DIGITS_OUT_PP-1:0] din;
input newbit;
integer k;
reg cin;
reg [3:0] digit;
reg [3:0] digit_less;
begin
cin = newbit;
for (k=0; k1)
begin
digit[3] = din[4*k+3];
digit[2] = din[4*k+2];
digit[1] = din[4*k+1];
digit[0] = din[4*k];
digit_less = digit - 5;
if (digit > 4'b0100)
begin
bcd_asl[4*k+3] = digit_less[2];
bcd_asl[4*k+2] = digit_less[1];
bcd_asl[4*k+1] = digit_less[0];
bcd_asl[4*k+0] = cin;
cin = 1'b1;
end
else
begin
bcd_asl[4*k+3] = digit[2];
bcd_asl[4*k+2] = digit[1];
bcd_asl[4*k+1] = digit[0];
bcd_asl[4*k+0] = cin;
cin = 1'b0;
end
end // end of for loop
end
endfunction
//--------------------------------------------------------------------------
// Module code
//--------------------------------------------------------------------------
// Perform proper shifting, binary ASL and BCD ASL
assign bin_next = {bin_reg,1'b0};
always @(bcd_reg or bin_reg)
begin
bcd_next <= bcd_asl(bcd_reg,bin_reg[BITS_IN_PP-1]);
end
// Busy bit, input and output registers
always @(posedge clk_i)
begin
if (rst_i)
begin
busy_bit <= 0; // Synchronous reset
dat_bcd_o <= 0;
end
else if (start_i && ~busy_bit)
begin
busy_bit <= 1;
bin_reg <= dat_binary_i;
bcd_reg <= 0;
end
else if (busy_bit && ce_i && bit_count_done && ~start_i)
begin
busy_bit <= 0;
dat_bcd_o <= bcd_next;
end
else if (busy_bit && ce_i && ~bit_count_done)
begin
bcd_reg <= bcd_next;
bin_reg <= bin_next;
end
end
assign done_o = ~busy_bit;
// Bit counter
always @(posedge clk_i)
begin
if (~busy_bit) bit_count <= 0;
else if (ce_i && ~bit_count_done) bit_count <= bit_count + 1;
end
assign bit_count_done = (bit_count == (BITS_IN_PP-1));
endmodule
ソース:https://ke.qq.com/user/tasks/index.html?cid=117307#tid=100127911&fr=2