EtherChannel Between a Cisco Catalyst Switch and Server Configuration Example
Network Diagram
ネットワークグラフ
This document uses this network setup:
このドキュメントは次のネットワークを使用しています.
Switch Configuration
スイッチ構成
In order to configure the switch, complete these steps.
Per the Network Diagram, choose the ports to be grouped:
次のポートを選択してetherchannelを作成
Gi 2/0/23
Gi2/0/24
For each of the listed ports, complete these steps:
リストされたポートについて操作します.
Configure the port as a Layer 2 switchport.
レイヤ2ポートに設定
Note: This step is required only for switches that support both Layer 2 switchports and Layer 3 interfaces.
3階層スイッチでのみ使用
Switch#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#int Gi2/0/23
Switch(config-if)#switchport
Switch(config-if)#
Configure the port as an access port and assign the appropriate VLAN.
VLANにインタフェースを追加
Switch(config-if)#switchport mode access
Switch(config-if)#switchport access vlan 100
Switch(config-if)#
Configure the port for spanning tree PortFast.
portfastの構成
Switch(config-if)#spanning-tree portfast
%Warning: portfast should only be enabled on ports connected to a single
host. Connecting hubs, concentrators, switches, bridges, etc... to this
interface when portfast is enabled, can cause temporary bridging loops.
Use with CAUTION
%Portfast has been configured on GigabitEthernet2/0/23 but will only
have effect when the interface is in a non-trunking mode.
Switch(config-if)#
Configure the port for EtherChannel with appropriate mode.
このEtherchannleモードを設定します.
Switch(config-if)#channel-group 1 mode active
LACP
Creating a port-channel interface Port-channel 1
Switch(config-if)#
Configure the EtherChannel load balancing. This configuration is applicable for all EtherChannels configured on this switch.
このEtherchannle負荷等化アルゴリズムを構成します.この構成は、スイッチ上のすべてのetherchannleに適用されます.
Switch(config)#port-channel load-balance ?
dst-ip Dst IP Addr
dst-mac Dst Mac Addr
src-dst-ip Src XOR Dst IP Addr
src-dst-mac Src XOR Dst Mac Addr
src-ip Src IP Addr
src-mac Src Mac Addr
Switch(config)#port-channel load-balance src-mac
MAC
Switch(config)#
Server Configuration
In order to configure the server, complete these steps:
次のステップでサーバの構成を完了します.
Start the NIC configuration utility.
Note: This examples uses the HP Network Configuration Utility 7. In order to use the HP Network Configuration Utility, locate the icon in the Windows 2000 system tray or click
Start > Settings > Control Panel > HP Network.
このNICユーティリティ構成ソフトウェアを開きます.
note:この例ではHP network configuration utility 7を使用しています.デスクトップアイコンをクリックするか、スタート-設定-コントロールパネル-hp networkをクリックしてソフトウェアを開くことができます.
Highlight both NICs, and the click
Team.
2つのNICをハイライトします.チームの選択
The NIC team is created.
このNICグループが作成されました
Click
Properties.
クリックのプロパティ
In the Team Properties windows, choose the appropriate Team Type Selection.
Note: Since this example configured the switch with LACP, choose the option with IEEE 802.3ad.
このプロパティダイアログボックスでetherchannelで使用するプロトコルタイプを選択します.
LACP IEEE 802.3 adの選択
Choose the required method from the Transmit Load Balancing Method drop-down list, and click
OK.
ドロップダウン・ダイアログ・ボックスで、ロード・バランシングのアルゴリズムを選択します.OKを選択します.
In the Team Properties window, click
OK, and when the confirmation window appears, click
Yes to continue.
このグループのプロパティウィンドウに入り、OKをクリックします.プログラム構成ウィンドウでYESを選択して続行
A dialog box appears that displays the status of the process.
このダイアログボックスは処理中です
When you are prompted to reboot the server, click
Yes.
再起動する必要があることを示します.YESを選択
Once the server is rebooted, open the network configuration utility in order to verify the teaming status.
サーバーを再起動した後、このネットワーク構成ユーティリティを開いて、このHP network teamが正常な状態かどうかを確認します.
Right-click
My Network Places. An additional network card,
Local Area Connection 3, displays in the window.
ネットワークリンクのローカルリンクの表示3
Configure the connection with static IP address, default gateway, and DNS/WINS settings or for dynamic configuration.
IPアドレス、カスタムゲートウェイ、DNS/WINサーバの構成、または動的取得の選択
Verify
検証#ケンショウ#
show etherchannel summary—Displays a one-line summary per channel group.
このetherchannleの詳細を表示
Switch#show etherchannel 1 summary
Flags: D - down P - in port-channel
I - stand-alone s - suspended
H - Hot-standby (LACP only)
R - Layer3 S - Layer2
U - in use f - failed to allocate aggregator
u - unsuitable for bundling
w - waiting to be aggregated
d - default port
Number of channel-groups in use: 1
Number of aggregators: 1
Group Port-channel Protocol Ports
------+-------------+-----------+-----------------------------
1 Po1(SU) LACP Gi2/0/23(P) Gi2/0/24(P)
Switch#
show spanningtree interface—Displays spanning tree information for the specified interface.
この集約ポートの生成ツリーの詳細を表示します.
Switch#show spanning-tree interface port-channel 1
Vlan Role Sts Cost Prio.Nbr Type
---------------- ---- --- --------- -------- ---------
VLAN0100 Desg FWD 3 128.616 P2p
Switch#
show etherchannel load-balance—Displays the load-balance or frame-distribution scheme among ports in the port channel.
現在のetherchannel負荷等化で使用されているアルゴリズムを表示
Switch#show etherchannel load-balance
EtherChannel Load-Balancing Operational State (src-mac):
Non-IP: Source MAC address
IPv4: Source MAC address
IPv6: Source IP address
Switch#
Troubleshoot
There is currently no specific troubleshooting information available for this configuration.
この構成に関するエラー情報は現在ありません.